Why Do You Need Pre Terminated Fiber Solutions?
                     Why Do You Need 
Pre Terminated 
Fiber Solutions?
INTRODUCTION
Today’s modern data center proposition continues to promote 
the hot topics around consolidation, reduced operating expense, 
flexibility, scalability and of course being as ‘Green’ as possible 
along the way. 
When you are building a custom fiber network it is essential to 
purchase quality cable assemblies. Never waste time or money 
terminating fiber cable in the field again. Save yourself and your 
team lot of time and trouble, and eliminate all performance 
worries with Pre Terminated Fiber Cable from FalconTech. You’ll 
get top-quality fiber cable that’s built to your exact specs, fully 
tested, and shipped ready for installation so you can take care of 
business. Below you will find information on standard options 
and components available for Pre Terminated Fiber Optic Cable 
assemblies. 
PRE TERMINATED FIBER OPTIC CABLE :
A Pre Terminated Fiber optic cabling system is one that 
contains cables and the necessary modular components with the 
accompanying connectors already attached. For optimum quality 
assurance, each part of the system is tested before it is shipped 
to the customer. A pre terminated fiber optic cabling system 
may contain any of the following, depending on the customer’s 
needs:
 Comes with a Swivel Pulling Eye :  
A swivel pulling eye is attached to protect against stresses 
associated with pulling the fiber optic assembly into position 
during installation. The pulling eye acts as a strain relief by 
distributing the stress over the outer jacket and eliminating it 
from the fiber optic strands. 
Continue....
 Comes on a Triple Flange Spool :  
Long preterminated fiber optic assemblies are shipped on a 
trPipRleE fl aTnEgRe MspIoNolA toT EprDov iFdIeB pEroRte OctiPonT IfoCr  the connectors on 
both ends. The additional flange also allows the end of the 
aCssAemBbLlEy  t:o remain safely coiled and protected from bending, 
twisting and tangling while the cable is run out. The inner end 
can then be unwound and connected.
 Direct Burial : 
Direct-Buried Cable (DBC) is designed to be buried under the 
ground without any additional covering, conduit or sheathing to 
protect it. This Outside Plant (OSP) fiber optic cable includes 
water-blocking characteristics and an armored jacket to prevent 
damage from rodents and the pressure created by the 
surrounding dirt and rock.
 Interlocking Armor : 
Fiber optic distribution cable encased in interlocking aluminum 
armor is ideally suited for harsh environments such as direct 
buried outside plant applications, industrial and heavy traffic 
areas, and data centers where cables are installed under the 
floor.
Continue....
 Indoor/Outdoor : 
Indoor/Outdoor cable (I/O cable) is designed to withstand the environmental conditions experienced 
oPutRdoEo rTs.E DRrMy wINatAerT-bEloDck FinIgB fEeaRtu OrePs, TsuICch  as water-swellable Aramid, protect against water ingress. 
CABLE :
 Aerial Cable : 
Aerial rated cable is strong enough to withstand the tension between structures through the incorporation 
of a strengthening feature such as a messenger cable or a central strength member.
 Tini Armor Uni-Boot : 
This cable option features fiber optic cable encased in a small 
OD stainless steel miniature armor. The 3mm outside diameter is 
more than 65% smaller and 75% lighter than standard 
interlocking armor and still maintains flexibility. The coiled armor 
offers protection and durability and may eliminate the need for 
conduit.
 Plenum / PVC : 
The plenum options include OFNP (Optical Fiber Nonconductive 
Plenum) and OFCP both of which have the fire-resistant and low smoke 
producing characteristics needed to meet The NEC requirements for 
cabling installed in a plenum space and not residing in conduit.
AVAILABLE CABLE TYPES :
PRE TERMINATED FIBER OPTIC 
CABLE :
Now you can install your own fiber optic cables without 
investing in training and equipment. Custom Factory 
terminated, pre-tested and ready to pull. Made to lengths 
of up to 5000 feet. These assemblies can be ordered in 
either indoor or outdoor variations, and in  6, 12 or 24 
strand fiber counts, in Multimode OM1, OM2, OS2,  OM3 
and OM4 or Singlemode!
 OM1 -- Falcon Technologies’ 
preterminated multimode OM1 fiber optic 
distribution assemblies utilize 62.5 micron 
Corning glass in a tight buffer design. 
These trunk cables provide a high speed 
infrastructure backbone pathway available 
in indoor/outdoor plenum (OFNP) and riser 
(OFNR); armored and non-armored.
Continue....
AVAILABLE CABLE TYPES :
 OM3/OM4 -- Falcon Technologies’ preterminated multimode OM3 and OM4 fiber optic 
distribution assemblies utilize 50 micron Corning glass in a tight buffer design. These 10 Gigabit, 
laser optimzed trunk cables provide a high speed infrastructure backbone pathway available in 
indoor/outdoor plenum (OFNP) and riser (OFNR); armored and non-armored.
 OS2 -- Falcon Technologies’ preterminated singlemode OS2 fiber optic distribution assemblies 
utilize 8.3 micron (sometimes seen as 9 micron in the nomenclature) Corning glass in a tight 
buffer design. These trunk cables provide a high speed infrastructure backbone in a long distance 
pathway available in indoor/outdoor plenum (OFNP) and riser (OFNR); armored and non-armored.
AVAILABLE CABLE TFYEPAETSU :RES AND BENEFITS :
 Lower Total Cost : Forget about costly connectors, consumables, and gear, 
plug the work, time, and testing required for field fiber optic link end. Our 
Pre Terminated fiber optic links spare where it matters most. FalconTech fiber 
links make end basic.
 Proven Performance : Get top execution with no field end errors. All Black 
Box pre-ended fiber links experience broad investigation and testing and 
accompany a lifetime ensure. Rely upon FalconTech for the majority of your 
fiber link needs.
 Quick Turnaround : Most FalconTech pre-ended fiber links are turned 
around in under seven days—now and then even in a day. Never be helpless 
before trusting that links will show up again.
AVAILABLE CABLE TYPES :
 Faster Deployments : Cut installation time and labor costs by 
70 to 80% with pre-terminated fiber cable. Because it arrives 
ready for work, deployments are as easy as plug-n-play. Fiber 
optic termination made easy.
 Fiber Cables Your Way : Just specify the core, cable type, 
jacket, connector, strand count, breakout, labeling, 
staggering, and if you want a pulling eye. With FalconTech, 
your fiber cable solutions feel custom made for you and your 
team.
AVAILABLE CABLE TYPECSO :NCLUSION 
Our fiber optic cables are made by 
FOA Certified technicians in the 
USA by Falcon Technologies Inc. 
using the latest epoxy injection 
and polishing systems for the 
highest quality and performance. 
The end faces of the Corning glass 
within our assemblies are machine 
polished, resulting in a much lower 
light loss than can be achieved by 
hand polishing. All pre terminated 
fiber products are guaranteed and 
100% tested.
AVAILABLE CABLE TYPESC O: NTACT US
 Next Day Service Available
 Falcon Made Assemblies In Usa
 Call 866-958-4499 For Immediate Service
Request A Quote
FIND US