No Hot Water After Replacing the Elements and Thermostat
                     No Hot Water After Replacing the Elements and Thermostat
We recognize how infuriating it can be to discover that your water heater
isn't heating water after putting so much time and effort into replacing the
components. Varied reasons are behind the no hot water, including a tripped
breaker, damaged wires, and improper replacement parts. Yet, it isn't limited
to it. Before consulting water heater repair San Jose professionals, utilize
the following tips to fix the issue. So let's proceed to it. 
Potential Reasons for No Hot Water After Replacing the Key Components!
First and foremost, allow at least 30 minutes or an hour for the water heater 
to heat the water, as sometimes water might take a while to warm up. If the 
problem persists, implement the below ways. 
 Tripped Circuit Breaker:
Examine the two pole breakers indicated for the water heater in your
home's  breaker  box to  determine  if  it's  stumbled or  fallen.  If  so,  it
might  be  the  source  of  all  this  upheaval.  Although why it's  tripped
requires  professional  inspection,  consider  pulling  up  the  breaker  to
solve your problem for the time being. However, if tripping recurred, it
signifies a short  circuit  in  the water heater,  necessitating calling an
electrician to fix the issue. 
 Draining Water Heater:
If the breaker hasn't been tripped, prefer flushing your water heater.
While you may not recall the last time you drained the water heater,
it's  one  of  the  foremost  reasons  for  getting  no  water  heater.  Scale
buildup may trigger multitudinous issues with your water heater. You
may call the  plumbers in San Jose for water heater draining if you
aren't feasible to do it. 
When  compared  to  gas  water  heaters,  electric  ones  build  up  scale
faster,  requiring you to flush and descale your tank at least once a
year. So, drain it now if you haven't emptied it in years. The unit will
probably start heating the water once you descale it. 
 Examine the Wiring Connections:
Inspect the wiring connections and ensure your technician has installed
essential  and  appropriate  parts  and  the  thermostat  if  the  problem
persists  after  descaling.  Loose  connections  or  broken  wires  may
decrease power, preventing the water from heating. However, before
inspecting  the cables  and connections,  turn  off the  power from the
breaker panel, or you can employ a water heater installation San Jose
expert to examine the issue. 
Related Article - How Do You Diagnose a Water Heater Problem
 Check the Heating Element and Thermostat for Consistency:
Consider testing your newly purchased thermostat and element first, as
one of the pieces may be defective. Test them using a multimeter and
a screwdriver. Commence by turning off the main power source and
unlocking  the  water  heater's  access  panels.  After  adjusting  your
multimeter to the lowest ohm value, unplug the wires attached to the
top element and place the multimeter probes on element's each screw.
Now, take note of the reading; if  it's  between 10 and 12 ohms, the
element  is  operational.  It's  faulty  if  it's  extremely  low or  indefinite.
Subsequently, repeat the same process for the second one. 
If  the above-cited  steps  don't  solve the problem,  consult  an experienced
electrician to help you discover and fix the issue. Additionally, consider your
water heater's  lifespan.  Usually,  their  average lifespan is  12 years.  If  it's
older, it's high time to replace your water heater with a more energy-efficient
tankless water heater. 
--------- Article Source ---------
https://www.emergencyplumbersca.com/no-hot-water-after-replacing-the-elements-and-thermostat/