Get Real Avaya 71300X Exam Questions answers - DumpsforSure
                      
 
Avaya
 
71300X
Avaya Aura Communication App lications Integration Exam
 
 
https://www.dumpsforsure.com/avaya/71300x-dumps.html
 
 
Question: 1 
   
By default, which Codec does Avaya Aura® Messaging (AAM) support? 
 
A.  G.726 
B.  G.722 
C.  G.711 
D.  G.729 
 
Answer: C     
 
Explanation 
You must configure the Messaging system to use the G.711 encoding format. 
Note: The G.711 format provides the highest audio quality especially when voice networks use multiple 
encodings and decodings. Avaya requires that you use the G.711 encoding format in Messaging systems 
that support TTY devices. 
The G.711 encoding format uses a higher encoding rate than GSM. The G.711 encoding format therefore 
produces larger files and requires more storage space for messages. Messaging provides customers with 
adequate storage space for message playback and networking. 
References: Administering Avaya Aura® Messaging, Release 6.2 Issue 2.2 (December 2013) , page 201 
https://downloads.avaya.com/css/P8/documents/100172127 
Question: 2 
   
After running the Install wizard on Avaya Session Border Controller for Enterprise (SBCE), you added a 
Public Outside IP address to the B1 interface. You try to ping this IP address from a PC in the same 
subnet but it falls. 
What would you do first to resolve the issue? 
 
A.  Restart Applications. 
B.  Set the Default Gateway router IP address, navigate to the Interfaces and Enable the B1 Interface. 
C.  Reboot SBCE. 
D.  Navigate to Device Specific Settings > Network Management > Interfaces and Enable the B1 
interface. 
 
Answer: D     
 
Explanation  
The interface might need to be enabled. 
 
 
2. Click on the Interface Configuration tab. 
 
3. Click the Toggle link for both the A1 and the B1 interfaces. 
The Administrative Status for both A1 and B1 changes to Enabled  
References: Avaya Aura Session Border Controller Enterprise Implementation and Maintenance (2012), 
 
Question: 3 
   
Which component converts WebRTC Media Stream to SIP Media Stream? 
 
A.  HTTP Reverse Proxy 
B.  Avaya Aura® Media Server (AAMS) 
C.  STUN/TURN server 
D.  G.450/430 or G.650 Medpro board 
 
Answer: C     
 
Explanation 
Provisioning Avaya Aura® Media Server for the WebRTC Snap-in. 
 
Procedure 
1. Log in to the Avaya Aura® 
Media Server Element Manager. 
2. Check that Avaya Aura® 
Media Server nodes and routes are set up correctly. 
See Deploying Avaya Breeze™ for details on configuring Avaya Aura® 
Media Server for Avaya Breeze™. 
3. Go to System Configuration > Server Profile > General Settings, enable Firewall NAT Tunneling Media 
Processor and then click Save. 
4. Go to System Configuration > Signaling Protocols > SIP > General Settings, enable Always use SIP 
default 
outbound proxy, and then click Save. 
Go to System Configuration > Media Processing > ICE > TURN/STUN Servers > Accounts and create a 
TURN/STUN account. This account ID and password must match the account created on the Avaya SBCE. 
6. Go to System Configuration > Media Processing > ICE > TURN/STUN Servers > Servers to add the 
TURN/STUN connection to the Avaya SBCE server 
Etc. 
References: Avaya WebRTC Snap-in Reference, Release 3.1 (May 2016), page 23 
https://downloads.avaya.com/css/P8/documents/101013939 
Question: 4 
   
Which two options describe the purpose of TraceSM in the Avaya Aura® Presence Services? (Choose 
two.) 
 
A.  It captures Packet-Size statistics from every telephone call in Avaya Aura® 7. 
B.  It captures real-time XMPP traffic. 
C.  It captures Voice and Video Calls media packets in real-time. 
D.  It captures live traces for both SIP and H323/XMPP clients. 
E.  It captures Contact details from every user connected to Avaya Aura® Presence Services. 
 
Answer: B D     
 
Explanation 
It’s important to know that traceSM is a real-time capture tool. 
traceSM is an interactive perl script that allows an administrator to capture, view, and save call 
processing 
activity on a Session Manager. While not as powerful or versatile as wireshark, traceSM is absolutely 
essential 
when it comes to working with Avaya SIP. First off, it allows you to view SIP messages even if they have 
been encrypted with TLS. 
References: https://andrewjprokop.wordpress.com/2014/06/02/a-necessary-guide-to-the-avaya-
tracesm-utility/ 
Question: 5 
   
 
What are the three components of Avaya Aura® Messaging (AAM)? (Choose three.) 
 
A.  Messaging Distributor 
B.  Application Server 
C.  Messaging Store 
D.  AxC/Directory 
E.  SM100 Module 
 
Answer: B C D     
 
Explanation 
The AXC connector is always co-resident with the Avaya message store.  
 
References: Administering Avaya Aura® Messaging Release 6.2, Issue 2.2 (December 2013) 
https://downloads.avaya.com/css/P8/documents/100172127 
Question: 6 
   
What is the process for establishing a command line session to the AES Management IP Address, and 
logging in with the default account and default password? 
 
A.  Use PuTTY to Rlogin to > AES Management IP Addr > using port 21, then enter login=admin 
password=admin. 
B.  Use PuTTY to SSH to > AES Management IP Addr > using port 22, then enter login=craft 
password=crftpw. 
C.  Use PuTTY to SSH to > AES Management IP Addr > using port 22, then enter login=cust 
password=custpw. 
D.  Use PuTTY to SSH to > AES Management IP Addr > using port 222, then enter login=admin 
password=admin01. 
 
Answer: B     
 
Explanation 
Use port 22, not port 21 or port 222. 
Log in as craft and use the default password. 
 
References: Application Enablement Services Installation and Upgrade Guide for a Bundled Server 
Release 
4.0, page 29 
https://downloads.avaya.com/elmodocs2/AES/4.0/02_300356_4.pdf 
Question: 7  
   
In Avaya Aura® System Manager, how is Avaya Aura® Messaging (AAM) added to the list of Managed 
Elements? 
 
A.  It is added when you configure the AAM SIP Entity in SMGR. 
B.  It is automatically added during the enrollment process. 
C.  It can only be manually added. 
D.  It is automatically added using initTM –f command on the Command Line Interface of AAM. 
 
Answer: D     
 
Explanation 
In System Manager, element installation sets up the trust between System Manager and its managed 
elements. 
. Similarly, UCM has a trust management process to set up the trust between UCM and its managed 
elements. 
To enable managed elements of UCM to be in the same trust domain as the System Manager managed 
elements, you must import the UCM Certificate Authority (CA) certificate to the System Manager 
managed 
element's trusted certificate list. 
Note: To force a re-initialization of trust management 
1. Ensure the enrollment password in the System Manager Security -> Enrollment Password screen is 
valid 
and set. Make note of this password as it will be needed when running the trust management 
initialization 
command. 
2. Log into the Session Manager virtual machine IP address with an ssh client as the craft or customer 
account 
login 
3. Execute the following shell command once at the shell prompt: 
$ initTM –f 
This will prompt you for the enrollment password and then initialize trust management and the 
database 
replication service of the Session Manager. 
References: Administering Avaya Aura System Manager for Release 6.3.11 and later, Release 6.3, Issue 
8, 
November 2016, page 1073 
https://downloads.avaya.com/css/P8/documents/101008185 
https://downloads.avaya.com/css/P8/documents/100161692 
 
Question: 8 
   
On Avaya Session Border Controller for Enterprise (SBCE), which statement about how to examine 
messages with Wireshark is true? 
 
A.  You have to start and stop the .pcap file using command line.  
B.  You can start and stop a Packet Capture in the EMS web GUI and then you can open the .pcap file 
with Wireshark. 
C.  Wireshark runs directly on Avaya Session Border Controller for Enterprise (SBCE). 
D.  They cannot be examined on this version. 
 
Answer: B     
 
Explanation 
Viewing the Packet Capture with Wireshark. 
0. Start a Packet Capture in the EMS web GUi. 
1. After the capture completes, click the Capture tab. 
2. Double-click on the capture file name. 
3. The File Download window opens. 
4. Click Open. 
The Wireshark application opens the trace. 
Note: The Wireshark call tracing tool can be used on virtual desktop for vLabs. 
References: Avaya Aura Session Border Controller Enterprise Implementation and Maintenance (2012), 
page 
468 
Question: 9 
   
Which statement about Avaya Aura® Presence Services 7.x snap-in licensing is true? 
 
A.  It requires an instance-license. 
B.  It requires a per-user license. 
C.  It does not require a license to work. 
D.  It requires a license file for each snap-in installed. 
 
Answer: C     
 
Explanation 
Presence Services snap-in does not require a license to work. 
References: Avaya Aura® Presence Services Snap-in Reference. Release 7.0.1 (December 2016), page 17 
https://downloads.avaya.com/css/P8/documents/101013646 
Question: 10 
   
 
Avaya Aura® Presence Services 7.x is implemented on Avaya Breeze™ (formerly known as Engagement 
Development Platform (EDP)). 
When looking at Elements > Engagement Development Platform > Service Management, which status 
would you expect for a Presence Services snap-in that is ready to support Avaya Aura® Presence 
Services? 
 
A.  Loaded 
B.  Installed 
C.  Accepting 
D.  Active 
 
Answer: C     
 
Explanation 
Enabling Avaya Breeze cluster running Presence Services 
Before you begin 
Ensure that the Avaya Breeze™ servers running the Presence Services are recovered / powered up. 
Procedure 
1. On the System Manager web console, navigate to Elements > Avaya Breeze > Cluster Administration. 
2. Select the Presence Services cluster, and change the Cluster State to Accept New Service. 
References: Avaya Aura® Presence Services Snap-in Reference. Release 7.0.1 (December 2016), page 48 
https://downloads.avaya.com/css/P8/documents/101013646 
 
https://www.dumpsforsure.com/avaya/71300x-dumps.html