Pre Terminated  Fiber Optic Cable Assemblies Usa
                     Pre Terminated 
Fiber Optic Cable 
Assemblies Usa
Falcon Tech Specialize in Pre Terminated Fiber Optic Cable 
assemblies to support data intensive networks, For your choice of 
multi mode Fibers OM1, OM3, OM4, single mode OS2 cables in 6, 12 
or 24 strand using the most popular connector types. Patch cords, 
Introduction hydra patch cords, MPO trunk assemblies and multi-fiber cable assemblies are available from Falcon Tech, offering convenience, 
reduced complexity, versatility and robustness. For more than 25 
years Falcon Technologies has been providing customers with high 
quality assemblies and sub assemblies. Delivering high quality 
products on time is our first priority.
1.       Comes with a Swivel Pulling Eye 
2.     Comes on a Triple Flange Spool 
3.     Direct Burial 
Pre Terminated 4.      Interlocking Armor
Fiber Products
5.      Indoor/Outdoor
6.      Aerial
7.      Tini Armor Uni-Boot
8.       Plenum / PVC
   1  .       Comes with a Swivel Pulling Eye :
A swivel pulling eye is attached to protect against stresses associated with pulling the fiber optic 
assembly into position during installation. The pulling eye acts as a strain relief by distributing the 
stress over the outer jacket and eliminating it from the fiber optic strands. Fiber assemblies will 
often twist during installation causing breakage of the strands. The swivel feature of the pulling eye 
prevents this twisting. The fiber optic connectors are encased in the mesh sheathing of the pulling 
eye to prevent damage and make it easier to pull the assembly through conduit, duct, walls, etc.
   2  .      Comes on a Triple Flange Spool
Long pre Terminated fiber optic assemblies are shipped on a triple flange spool to provide 
protection for the connectors on both ends. The additional flange also allows the end of the 
assembly to remain safely coiled and protected from bending, twisting and tangling while the cable 
is run out. The inner end can then be unwound and connected.
   3  .       Direct Burial :
Direct-Buried Cable (DBC) is designed to be buried under the ground without any additional 
covering, conduit or sheathing to protect it. This Outside Plant (OSP) fiber optic cable includes 
water-blocking characteristics and an armored jacket to prevent damage from rodents and the 
pressure created by the surrounding dirt and rock.
   4  .      Interlocking Armor
Fiber optic distribution cable encased in interlocking aluminum armor is ideally suited for harsh 
environments such as direct buried outside plant applications, industrial and heavy traffic areas, 
and data centers where cables are installed under the floor. The armor is a flexible, metallic and 
crush resistant material helically wrapped around the fiber cable. The design reduces installation 
costs by eliminating the need for duct or conduit and their associated material and labor costs.
   5  .       Indoor/Outdoor :
Indoor/Outdoor cable (I/O cable) is designed to withstand the environmental conditions 
experienced outdoors. Dry water-blocking features, such as water-swellable Aramid, protect 
against water ingress. Materials used in the manufacture of the outer jacket are weather resistant 
and fungus resistant. UV resistance allows the fiber optic cable to withstand long-term exposure to 
sunlight without degradation.
   6  .      Aerial :
Aerial rated cable is strong enough to withstand the tension between structures through the 
incorporation of a strengthening feature such as a messenger cable or a central strength member. 
The messenger design will have the fiber optic cable lashed to the messenger cable in a figure-8 
configuration. Cable with a central strength member will have loose tube fiber surrounding a 
central element composed of steel or all-dielectric (known as All-Dielectric Self-Supporting or 
ADSS).
   7  .       Tini Armor Uni-Boot :
This cable option features fiber optic cable encased in a small OD stainless steel miniature armor. 
The 3mm outside diameter is more than 65% smaller and 75% lighter than standard interlocking 
armor and still maintains flexibility. The coiled armor offers protection and durability and may 
eliminate the need for conduit. This reduces the weight and surface area when compared to 
standard cable design, which helps to improve airflow within the data center. The single boot also 
allows for reversing polarity within the connector body.
   8  .      Plenum / PVC :
The plenum options include OFNP (Optical Fiber Nonconductive Plenum) and OFCP (Optical Fiber 
Conductive Plenum, which is armored) both of which have the fire-resistant and low smoke 
producing characteristics needed to meet The NEC (National Electrical Code) requirements for 
cabling installed in a plenum space and not residing in conduit. Plenum rated cable is typically 
constructed with fluorinated ethylene propylene (FEP) which will self-extinguish, not reignite and 
will produce less smoke than a non-plenum cable.
Available Cable Types
For your choice of multi mode Fibers OM1, OM3, OM4, single mode OS2 cables in 6, 12 or 24 strand 
using the most popular connector types. Available indoor outdoor, PVC plenum, armored and non-
armored configurations.
 OM1 :  
Falcon Technologies’ Pre-Terminated multimode OM1 fiber optic distribution assemblies utilize 62.5 
micron Corning glass in a tight buffer design. These trunk cables provide a high speed infrastructure 
backbone pathway available in indoor/outdoor plenum (OFNP) and riser (OFNR); armored and non-
armored.
 OM3/OM4 :  
Falcon Technologies’ preterminated multimode OM3 and OM4 fiber optic distribution assemblies 
utilize 50 micron Corning glass in a tight buffer design. These 10 Gigabit, laser optimzed trunk cables 
provide a high speed infrastructure backbone pathway available in indoor/outdoor plenum (OFNP) 
and riser (OFNR); armored and non-armored.
 OS2 :  
Falcon Technologies’ preterminated singlemode OS2 fiber optic distribution assemblies utilize 8.3 
micron (sometimes seen as 9 micron in the nomenclature) Corning glass in a tight buffer design. 
These trunk cables provide a high speed infrastructure backbone in a long distance pathway available 
in indoor/outdoor plenum (OFNP) and riser (OFNR); armored and non-armored.
Available Connector Types
We keep the following connector types in stock to ensure that we may begin your order 
immediately:
 SC (Multi-Mode 62.5 micron and 50 micron, Single-Mode, 10 Gig)
 ST (Multi-Mode 62.5 micron and 50 micron, Single-Mode, 10 Gig)
 LC (Multi-Mode 62.5 micron and 50 micron, Single-Mode, 10 Gig)
 FC (Multi-Mode 62.5 micron and 50 micron, Single-Mode, 10 Gig)
 MTRJ (Multi-Mode 62.5 micron and 50 micron, Single-Mode, 10 Gig)
 MTP 12 fiber and up (10 Gig)
 Angle Polish (APC) FC (Single-Mode)
 Angle Polish (APC) SC (Single-Mode)
High Quality Guaranteed
Our fiber optic cables are made by FOA (Fiber Optic 
Association) Certified technicians in the USA by Falcon 
Technologies Inc. using the latest epoxy injection and 
polishing systems for the highest quality and 
performance. The end faces of the Corning glass within 
our assemblies are machine polished, resulting in a 
much lower light loss than can be achieved by hand 
polishing. All Pre-Terminated Fiber products are 
guaranteed and 100% tested. Each assembly is 
individually scoped and tested for light loss to exceed 
minimum requirements for TIA test standards. Loss 
results are included with each assembly.
 Next Day Service Available
 Falcon Made Assemblies In Usa
 Call 866-958-4499 For Immediate Service
Request A Quote
FIND US