Quick Fixes for Your Hot Water System Prevent Cold Showers 
                     QUICK FIXES 
FOR YOUR 
HOT WATER 
SYSTEM: 
PREVENT 
COLD 
SHOWERS 
INTRODUCTIO
There's nNothing more annoying than anticipating warm water 
when you enter the shower and getting an icy blast instead. 
Although a broken hot water system can ruin your day, there 
are a few easy solutions you can attempt before contacting a 
professional. Making sure the hot water system is getting 
power is the first step in diagnosing a problem. Examine the 
circuit breaker and reset it if required for electric water 
heaters. If the breaker continues to trip, there may be a more 
serious electrical problem that needs to be fixed by a 
professional Hot Water System Repairs in Springwood. If your 
water heater runs on gas, make sure the pilot light is on. If it 
has gone out, safely light it by following the manufacturer's 
directions. You might need to call a specialist or check the 
gas supply if the pilot light won't stay lit. We'll discuss typical 
problems with hot water systems in this blog, along with 
effective troubleshooting techniques. 
ADJUST THE THERMOSTAT/FLUSH 
THE TANK TO REMOVE SEDIMENT 
Sometimes a thermostat set too low is the only cause of lukewarm water. 
Check your water heater's thermostat and set it to a temperature between 
120°F and 140°F (49°C to 60°C). The heating element in the unit can be 
broken if modifying the thermostat doesn't help. Your water heater's bottom 
may accumulate silt and mineral deposits over time, which will lower 
performance and result in uneven water temperatures. Restoring proper 
function may be aided by flushing the tank. After emptying, turn on the water 
supply for a short while to remove any leftover sediment, then shut off the 
valve and fill the tank again. An excessive amount of rust or sediment could 
indicate that your water heater is getting old and needs to be replaced. 
Inspect the Heating Elements (For Electric 
Heaters)/Check for Leaks 
Heating elements are what electric water heaters use to warm the water. 
Should one of these components malfunction, you can get cold or 
lukewarm water. You can use a multimeter to test the elements and replace 
them if necessary if you're comfortable doing simple do-it-yourself repairs. 
But it's preferable to speak with an expert if you're not sure. Insulate Your 
Pipes and Tank/Address Low Water Pressure Issues 
Heat loss from uninsulated pipes may be the cause of your water's 
temperature fluctuations, especially during the winter. Insulating exposed 
pipes can increase heat retention and boost your hot water system's 
efficiency. A thermal blanket can also be used to insulate the water heater 
tank, preventing heat loss and lowering energy usage.  
Future issues can be avoided with routine maintenance, 
such as insulating pipes, adjusting the thermostat, and 
flushing the tank. To keep your hot water running 
properly, don't be afraid to get professional 
Hot Water System Repairs in Springwood help if the 
problem continues. You can guarantee that your hot 
water system runs well and take warm showers all year 
long by being proactive. An important safety feature 
that relieves excess pressure from the water heater is 
the TPR valve. A malfunctioning valve may result in 
inconsistent water temperature or possibly equipment 
damage. These simple troubleshooting techniques can 
resolve a lot of hot water system problems, but in some 
Dcisacslaeimse, rp: Trhoisf eiss gseinoenriac lI nafosrsmiasttioann &c epo isst;  ncoencteenst sabaoruyt.  the services can be 
changed from time to time as per your requirements and contract. This is written 
for only SEO purposes; we are not claiming it is 100% accurate as it's general 
content. The images we use in this context have been taken from the official 
websites Canva. To get the latest and updated information, contact us today or 
visit our website.
CONTACT US
Phone
0481 187 068
Email
[email protected]
Website
https://bluemountainsplumbing.net.au/
Location
Plumbers & Gas Fitters 
 Glenbrook, NSW 2773, Australia