What To Do If My Washing Machine Does
                     What To Do If My Washing 
Machine Does Not Spin
What To Do If My Washing Machine 
Does Not Spin
WASHING MACHINE REPARI & 
SERVICE
The door handle of a washing machine is a very fragile part. Therefore, 
if it has broken or gives you problems and sometimes even does not 
allow you to open the door to put your clothes in or out, you will want 
to change the door lock of the top-loading washing machine. And it's 
very simple.
Although if you don't know how to do it, it may take several hours. 
Therefore, it is important that you have the right tools and that you 
follow the steps that we teach you one by one.
WASHING MACHINE REPARI & 
SERVICE
 How does a top-load washing machine door latch work?
 The door handle of the washing machine can wear out over the 
years. It is very common for one of its parts to wear out or 
simply break inside. In fact, its break in most cases is not visible.
 In most cases, this break appears after a little struggle with the 
door and in many cases due to a too-strong pull.
 For this reason, it is always recommended that you wait a few 
minutes to make sure that you can open the door calmly and 
without incident.
WASHING MACHINE REPARI & 
SERVICE
 Causes of the problem in closing the top-loading washing machine
 Replacing the door lock on a top-loading washing machine can be quite tricky if you don't know 
exactly what caused it or where the problem is.
 Sometimes the break is internal and in others, there is a blockage. However, if you can't figure out 
why, don't worry, there are some steps you can take to fix the shooter issue even if you don't know 
the problem.
 What you need before changing the lock on your washing machine door
 But before you start you have to prepare yourself. What do you need to change the door lock of the 
top-loading washing machine? Not much.
 In principle, a screwdriver or wrench (preferably both) and pliers are enough.
 All three are cheap and easy-to-acquire tools. Plus you don't need anyone else's help.
 But in addition, you probably should buy a spring and a shaft to replace the ones on the inside of 
your washing machine door.
WASHING MACHINE REPARI & 
SERVICE
 Steps to change the top-loading washer door lock
 To change the door lock on a top-loading washer, you always have to remove the door. This also 
applies to front-loading washing machines.
 Step 1
 First of all, you have to loosen the screws on the door, which are usually small, so you will need a 
screwdriver for these measurements. Then, slightly lift the door before unscrewing it completely. 
Then the hinge will come loose.
 Step 2
 When the hinge is loose you have to loosen the screws on the inside of the door. This is done later 
because you didn't have access before.
 Well, now you can remove the metal or glass part and you can finally completely separate the 
handle or handle from the door.
WASHING MACHINE REPARI & 
SERVICE
 Step 3
 Now what you have to do is extract the innerspring and its axis. Probably this is the one that 
has broken its operation. What you should do is replace them with new ones. This is very 
easy but you need to make sure that the smaller tab on the inside fits snugly into the slot. If 
this were not the case, problems could arise again. Once you have changed them, return 
everything to its previous state. That is, you must put the metal or glass part back in its 
place and also place the interior frame. Then correctly place the lever handle on the frame 
and of course check that it moves and rotates correctly without forcing. It is also good that 
you notice that there is dampness.
 Step 4
 When you have verified that everything works correctly, it is time to screw. Just place the 
door of your top-loading washing machine in the correct position and start screwing. The 
best thing is that you do it with a screwdriver of the appropriate measures.
WASHING MACHINE REPARI & 
SERVICE
 Conclusion: how to change the top-loading washing 
machine door lock in a few minutes
 Changing the door lock on your top-loading washer is 
easy. At most, it will take you 20 minutes. The most 
important thing is that you have the right tools, that you 
find replacements for the spring, and finally that you 
have patience. If you follow the steps you can repair it in 
less than half an hour. Although if you don't know how to 
do it, it may take several hours. Therefore, it is important 
that you have the right tools and that you follow the 
steps that we teach you one by one.
ADDRESS
Name: Prepare Service
Address: No. 2/18, Kannika Nagar, TVS Nagar Road, 
Kavundampalayam, Coimbatore – 641030
Mobile: 9787669555
E-mail: [email protected]
Website: https://prepareservice.in/